+31 (0)72 - 54 01 002

TyreON TSC4000X2A Alignment lift - On floor scissor lift - Wheels-free lifting system - 4.8m runways with Lighting - 4T

Capacity 4000 kg - On floor
Liftheight 216 cm (187 cm netto)
Runway LxW 480 cm / 60,8 cm
Drive motor 2,6 kW (400V/3Ph/C16A)
2nd scissor 4000kg H43cm L1.5 - 2m
Bonus features ►24V LED on runways
►Rails for rolling jack
►SUV Adapter set
►Hose sets + floor covers
Optional ►2.5 Ton rolling jack (TRJ25A)
►20 litres hydraulic fluid
Shipment to all countries except Germany
Voltage 400V
On Foor installation alignment scissor car lift with free wheel movement capability (in runways).
Display for reading the status of diverse functions of the scissor car lift.
The most robust and reliable 4T inground installation scissor car lift available.

Perfect balanced scissor car lift for accurate wheel alignment with about 1 meter of workspace between the tables.

TyreON TSC4000X2A Alignment scissor car lift - On Floor installation


  • Suitable for short and long passenger cars (multiple stretch extra large) vans and small lorries
  • The 4.8 meter long runways are 60.8 cm wide
  • Easy access - 64 cm wide ramps with anti-slip profile
  • With long scissors and oversized runways
  • Two hydraulic cylinders for heavy lifting
  • Manual override for descending in case of power outage (handpump)
  • Reduction valve - Control over descending speed
  • Safety valve (overload safety) - No damage to car lift in case of overload
  • Ascending/descending in about 60 sec.
  • Remote controlled lift of about 2,6 meter or less
  • Fully powder coated finish
  • Required air pressure 6 - 8 bar
  • The 64 cm wide ramps are 130.5 cm long and have 64 cm long extensions
  • Width 221,3 cm
  • The minimum length required for installation is 7 meters (including the ramps and 64cm extensions)
  • Weight of lift 2700 kg
  • Required depth concrete floor 15-20 cm - C20/25
  • Simple installation with system integrated depressurization and runway leveling out procedure
  • Controller  L x W x H (cm)  35,5 x 37 x 108

 

Free Wheel system and wheel alignment


With the extra long rear wheel plates and spacious recesses for turntables, the TSC4000X2A is suitable for aligning short and long chassis vehicles up to 4T.

  • Regular and 3D wheel alignment
  • Hydraulic free wheel system -  4000 kg - Lift height 43 cm
  • Extendable tables 150 - 200 cm.
  • Runways with cut-outs for turntables - shims included
  • Runways with built-in movable rear wheel plates - mechanically lockable
  • Xl rear wheel plates - 1.8 meter


Safety features - CE-Stop


  • Voltage through entire lift and control panel is only 24V
  • Automatic and accurate syncing function of the runways
  • CE-Stop: end height switch at 30 cm, additional manual input required for final stage of descending
  • Lowered descending velocity during final stage.
  • Acoustic and optical signal final stage of descending
  • Hydraulic shut-off valve
  • Tube failure safety system
  • Automatic safety lockup - 19 lock positions
  • Automatic unlocking of safety safety system (air)
  • Built-in sensor shuts down engine at maximal level


With Bonus features as standard 

 



  • 4T Capacity
  • 216 cm Lifting height
  • Alignment
  • Free wheel system with extendable platforms
  • 4.8 meter runways
  • 4 rubber lifting blocks
  • Mounting on the floor

  • Integrated 24V LED-lighting with roster shield
  • Rails for support of optional lift jack

  • Low profile ramp extensions
  • For cars with very small ground clearance

  • Hydraulic tube set
  • Air tube set
  • Floor covers
  • Groundanchors

CE-certification

Scissor inground installation alignment car lift

The TyreON TSC4000X2A is CE certificated and meets the following safety standards

• EN1493:2010 Vehicle Lifts
• EN 60204-1:2006+AC:2010 Safety of machinery - Electrical equipment of machines - Part1: General requirements
• EN ISO 12100:2010 Safety of  machinery – general principles for design – Risk assessment and risk reduction
In stock
€9.000,- €9.250,-
The price is excluding tax and delivery costs

Information-request

Interested in the TyreON TSC4000X2A Alignment lift - On floor scissor lift - Wheels-free lifting system - 4.8m runways with Lighting - 4T? Request an offer.
In stock
€9.000,- €9.250,-
The price is excluding tax and delivery costs

Optional with the alignment scissor car lift in floor 



  • 2.5 Ton rolling jack (TRJ25A)
  • 43 cm lift without adapters
  • 2 adapters 8 cm
  • Width 766 up to 1626 mm
  • €895,- excl. VAT

  • TyreON TOP160 SUV Adapter set
  • Set of 2 crossbeams for small framed vehicles, SUV's €290,- excl. VAT

Packaging


  • TSC4000X2A   L490 x B65 x H75 cm - 2400 kg
  • Controller, powerunit and a set LED runwaylights L120 x B70 x H50 cm - 50 kg
  • Box with hydraulic hose sets, hose floor covers and mounting materials  L185 x B70 x H35 cm - 200 kg
  • Optional TOP160 SUV adapter set L170 x B25 x H25 cm - 50 kg
  • Optional TRJ25A 2.5T rolling jack  L95 x B60 x H35 cm - 100 kg